Fiberglass cloth 10 oz. plain weave 50 inch wide volan

Fiberglass cloth 10 oz. plain weave 50 inch wide volan

Volan Finish For Epoxy Resin Compatibility
Equal Strength in Warp and Fill Direction
Use this fiberglass cloth when high strength parts are desired. It is ideal for construction, composites reinforcement, mold making, aircraft and auto parts tooling, marine and other composite lightweight applications. Volan is also known as Chrome Finish due to presence of chromium applied to glass fibers. The Volan sizing or finish is applied to fiberglass fabric during the manufacturing process to give good bonding to epoxy, vinyl ester and polyester resins. If used with clear resins, volan cloth will appear to have a slight greenish tint; Volan laminates tend to dent rather than crack making it an ideal fabric for high impact applications.
PLEASE CHECK OUT OUR NEW APPLICATIONS AND USAGE HELP PAGE TO LEARN MORE ABOUT COMPOSITE FABRICATION TECHNIQUES
Please click on the link for lengths greater than 10 yards
For multiple yard purchase, request for an invoice and
(3 feet length by 50 inches wide per unit)
The minimum cut length is 1 yard by 50 inches. Multiple yard purhace will be uncut and continuous.
Folded and packaged in sealed bag
Cut lenght greater than 10 yards will be supplied rolled on cardboard core
USE THESE EPOXY RESIN SYSTEM WITH THIS FIBERGLASS FABRIC
MAX BOND LOW VISCOSITY FOR MARINE APPLICATIONS
MAX GPE FOR GENERAL CONSTRUCTION LOW COST APPLICATIONS
MAX CLR HP CRYSTAL CLEAR HIGH PERFORMANCE APPLICATION
10 Ounce Fiberglass 25 layers Impregnated with MAX GPE White
Wet-Lay-up Engine Cowling Test Panel
10 Ounce Fiberglass 25 layers Impregnated with MAX GPE White
PolymerProducts, The Epoxy Experts
Is Now Your One Stop SourceFor All Your Composite Fabric Needs MADE IN THE USA We Have Just Acquired Thousands Of Yards · Fiberglass Fabrics· Carbon Fiber Cloth· Aramid Fabrics· Aluminum and Phenolic Honeycomb Cores Factory woven by one of the largest weavers and producers of composite fabrics for aerospace, marine, electronic and structural composite materials. CLICK ON THE PICTURE TO PAUSE SLIDE SHOW
In this most simple weave pattern, warp and fill yarns are interlaced over and under each other in alternating fashion. The plain weave provides good stability, porosity and the least yarn slippage for a given yarn count. Mock Leno
The mock leno weave is used where relatively low numbers of yarns are involved. The leno weave locks the yarns in place by crossing two or more warp threads over each other and interlacing with one or more filling threads. Four Harness Satin (Crowfoot)
The four harness satin weave is more pliable than the plain weave and is easier to conform to curved surfaces typical in reinforced plastics. In this weave pattern there is a three by one interfacing where a filling yarn floats over three warp yarns and under one. Eight Harness Satin
The eight harness satin is similar to the four harness satin except that one filling yarn floats over seven warp yarns and under one. This is a very pliable weave and is used for forming over curved surfaces. Twill weave
This twill weave is more pliable than the plain weave and has better drapability while maintaining more fabric stability than a four or eight harness satin weave. The weave pattern is characterized by a diagonal rib created by one warp yarn floating over at least two filling yarns. Chrome Finishes (Volan A) F-16 & F-3Heat cleaned fabric is saturated in a methacrylate chromic chloride solution, cured, and washed to remove any soluble salts. Both F-16 and F-3 are Volan type finishes with F-3 being a high chrome content version. Used with polyesters, phenolics, and epoxies, F-16 and F-3 fabrics make a light green laminate.For Technical SupportPlease Call (***) 673 1625Mon-Fri9:00 AM to 6:00 PM PSTPlease inquiry for volume discount.